• Garbage Disposal Replacement

    Garbage Disposal unitWhether you’re replacing an old garbage disposer or installing a new one, it’s an easy job. You don’t need to be a master plumber or a licensed electrician to complete the job effectively. It does help if you know a little bit of each, however these instructions should help even if you don’t.

    Always shut off the power to the circuit that will serve the disposal before beginning any work. If you’re replacing a disposal, turn off the electricity to that circuit and unplug the disposal or disconnect the wiring before removing the unit. Test the bare ends of the wires with an digital multimeter to make sure they are not charged. To provide better access and make the work easier, you may be able to temporarily remove the cabinet doors under the sink. When working under the sink, wear safety glasses.

    Some tools you will need

    • A bucket and some rags
    • Plumbers putty
    • Putty knife
    • Screwdrivers
    • Hammer
    • Wire strippers
    • Wire nuts and electrical tape
    • Pipe wrench or tongue and groove channellocks

    Installation Steps

    1. J Trap InstallationAfter cleaning out everything under your sink, the first step is to remove the existing strainer from the sink. Under the sink, place the bucket under the “J” trap. Use the pipe wrench or channellocks to loosen the slip nuts and remove the “J” trap. Dump the water in the bucket.
    2. With the “J” trap removed, look for the large nut that holds the strainer in place. Remove the nut.
    3. Remove the strainer and clean up any old plumber’s putty that was left behind. You may need to use the putty knife to pry the strainer up to remove it. It’s important that the sink be totally clean of old putty and debris.
    4. The next step is to open the new garbage disposer and install it. The first piece you’ll need is the sink flange and mounting assembly. The mounting assembly consists of an upper mounting ring, a lower mounting ring and the mounting bolts. Take a nice amount of plumbers putty and form a ring around the drain. Take the sink flange and set it in the drain. Press it down slightly onto the putty.
    5. Under the sink, take the gasket and mounting ring and slide them up the flange. You may need a second pair of hands to keep the flange stable on the top side. There should be a snap ring that you can connect to the flange to keep the gasket and ring secure.
    6. Tighten the mounting bolts to bring everything together. There are three bolts, and it’s important to tighten them evenly through the process. As the mounting assembly tightens, plumbers putty will squeeze out from under the flange in the sink. That’s OK – simply wipe the excess away.
    7. The Reset ButtonNow it’s time to wire the disposer. On the bottom side of the disposer you should see 1. A red reset button, 2. A flywheel turning wrench hole, and 3. The cover plate for the electrical connections. Remove the cover plate. You should see a trio of wires – a black, a white and a green (or bare copper in some disposers).
    8. The garbage disposer kit should include the cord and plug, so remove it from the box. The wires should be pre-stripped, but if they’re not, use the wire strippers to remove about 3/4″ of insulation. The side of the disposer should have a hole with a romex connector already in place. Slide the cord through the hole so that the black cord sheath is under the connector’s metal. Tighten down the bolts on the romex connector to hold the wire in place.
    9. Use the wire nuts to make the necessary wire connections (black to black, etc.). Secure the wire nuts with electrical tape and neatly stuff the wires back into the chamber. Replace the electrical cover.
    10. If you do not have an installed dishwasher, you can proceed to the next step, but if you do have one, then there’s an extra step. On the side near the top of the disposer you will see a close-ended tube coming out the side. That is where the dishwasher inlet line gets hooked up to. Simply take a screwdriver and hammer and chisel out the plug. It will usually fall into the disposer, so just turn the disposer over and the piece of plastic will fall out. If you have no dishwasher, or if you have the mobile kind that hooks directly up to the faucet, then leave the plug in place.
    11. Now it’s time to mount the disposer. Under the sink, line up the disposer with the mounting assembly. You will see where the three “ears” on the disposer should lift into. Once the “ears” are into the assembly, turn the disposer to lock it into place. It could take a few tries and the disposer may get heavy, so just take your time and don’t get frustrated. You will feel it lock into place. You will still be able to slightly turn the disposer, but everything will get tightened down at the end.
    12. Next connect the plumbing. You may need to turn the disposer slightly to line everything up. If you have a dishwasher, the drain line gets connected to the inlet port that you knocked out earlier. Odds are the “J” trap you removed earlier will not line up with the garbage disposer, so you may have to cut some PVC plumbing pipes to make everything fit correctly. Be sure to use the nylon washers at each lock nut.
    13. Connect the plumbing and make sure all the lock nuts are tight and that the disposer line is tight. Near the mounting assembly is a rotating cam collar. With a screwdriver or wrench for leverage, tighten the collar down. This will lock the disposer into place and solidify the installation.
    14. locknutNow check for leaks. Turn the faucets on and let water flow through the disposer. Inspect every locknut and seal for leaks. Tighten anything that needs it. Turn your dishwasher on and make sure the connection to the disposer doesn’t leak. If everything stays dry, you’re good to go.
    15. Turn the power back on to the under sink outlet. Plug the disposer into the outlet and with the water running, hit the switch. You should hear the beautiful humming of your new disposer.

     

    Note – When connecting the pipes, make sure you slide the lock nut on the pipe first, then the nylon washer.

    Post Tagged with , ,
Comments are closed.